Features:
Applications:
RSPD-01C120-XX
155Mb/s 120km CWDM SFP Transceiver
Hot Pluggable, Duplex LC, +3.3V, 1270nm~1610nm, CWDM DFB-LD, Single-mode, DDM
Description:
FIBERWDM’s RSPD-01C120-xxTransceiver is a high performance, cost effective module which have a duplex LC optics interface. Standard AC coupled CML for high speed signal and LVTTL control and monitor signals. The receiver section uses a PIN receiver and the transmitter uses a 1270nm~1610nm CWDM DFB laser, up to 29dB link budge ensure this moduleSONETOC-3/SDHSTM-1 120km application.
Absolute Maximum Ratings
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Storage Temperature |
TS |
-40 |
|
+85 |
°C |
Supply Voltage |
VCC |
-0.5 |
|
4 |
V |
Relative Humidity |
RH |
0 |
|
85 |
% |
Recommended Operating Environment
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
|
Case operating Temperature |
Industrial |
TC |
-40 |
|
85 |
°C |
Extended |
-5 |
|
85 |
°C |
||
Commercial |
0 |
|
+70 |
°C |
||
Supply Voltage |
VCC |
3.135 |
|
3.465 |
V |
|
Supply Current |
Icc |
|
|
300 |
mA |
|
Inrush Current |
Isurge |
|
|
Icc+30 |
mA |
|
Maximum Power |
Pmax |
|
|
1 |
W |
Electrical Characteristics(TOP =-40 to85°C, VCC = 3.135 to 3.465 Volts)
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Note |
Transmitter Section: |
|
|||||
Input differential impedance |
Rin |
90 |
100 |
110 |
W |
1 |
Single ended data input swing |
Vin PP |
250 |
|
1200 |
mVp-p |
|
Transmit Disable Voltage |
VD |
Vcc – 1.3 |
|
Vcc |
V |
2 |
Transmit Enable Voltage |
VEN |
Vee |
|
Vee+ 0.8 |
V |
|
Transmit Disable Assert Time |
Tdessert |
|
|
10 |
us |
|
Receiver Section: |
|
|||||
Single ended data output swing |
Vout,pp |
300 |
|
800 |
mv |
3 |
Data output rise time |
tr |
|
|
500 |
ps |
4 |
Data output fall time |
tf |
|
|
500 |
ps |
4 |
LOS Fault |
Vlosfault |
Vcc – 0.5 |
|
VCC_host |
V |
5 |
LOS Normal |
Vlos norm |
Vee |
|
Vee+0.5 |
V |
5 |
Power Supply Rejection |
PSR |
100 |
|
|
mVpp |
6 |
Note:
1. AC coupled.
2. Or open circuit.
3. Into 100 ohm differential termination.
4. 20 – 80 %
5. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
6. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (CWDM SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.
Optical Parameters (TOP =-40 to85°C, VCC = 3.135 to 3.465 Volts)
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Note |
Transmitter Section: |
||||||
Center Wavelength |
λc |
λ-6 |
λ |
λ+7.5 |
nm |
|
Spectral Width |
σ |
|
|
1 |
nm |
|
Optical Output Power |
Pout |
0 |
|
5 |
dBm |
1 |
Optical Rise/Fall Time |
tr / tf |
|
|
500 |
ps |
2 |
Extinction Ratio |
ER |
10 |
|
|
dB |
|
Generated Jitter (peak to peak) |
JTXp-p |
|
|
0.07 |
UI |
3 |
Generated Jitter (rms) |
JTXrms |
|
|
0.07 |
UI |
3 |
Eye Mask for Optical Output |
Compliant with G.957(class 1 laser safety) |
|
||||
Receiver Section: |
|
|||||
Optical Input Wavelength |
λc |
1260 |
|
1620 |
nm |
|
Receiver Overload |
Pol |
-8 |
|
|
dBm |
4 |
RX Sensitivity |
Sen |
|
|
-34 |
dBm |
4 |
RX_LOS Assert |
LOS A |
-47 |
|
|
dBm |
|
RX_LOS De-assert |
LOS D |
|
|
-37 |
dBm |
|
RX_LOS Hysteresis |
LOSH |
0.5 |
|
|
dB |
|
General Specifications: |
||||||
Data Rate |
BR |
|
155 |
|
Mb/s |
|
Bit Error Rate |
BER |
|
|
10-12 |
|
|
Max. Supported Link Length on9/125μmSMF@155Mb/s |
LMAX |
|
80 |
|
km |
|
Total System Budget |
LB |
29 |
|
|
dB |
|
Note
1. The optical power is launched intoSMF.
2. 20-80%.
3. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253.
4. Measured with PRBS 27-1 at 10-12 BER
Mechanical Dimensions
Mechanical Drawing
Order Information:
In the Part No. ofRSPD-01C120-xx,xx stands for central wavelength, such as:
27: for 1270nm, 29: for 1290nm, 31: for 1310nm,……61: for 1610nm.
想知道这个产品吗?
如果您对我们的产品感兴趣并想了解更多详细信息,请在此处留言,我们将尽快答复您。