other

三叶偏振控制器

  • Low insertion loss
  • Wide wavelength range
  • Easy disassemble,self-replacement,winding fiber
  • 产品详细信息


The mechanical three-ring polarization controller

 

Product description

 

The mechanical three-ring polarization control is based on the principle of Birefringence produced by optical fiber under external force. The three rings are equivalent to λ/4, λ/2 and λ/4 wave plates, respectively. The light waves passing through λ/4 wave plates are converted into linearly polarized light, and the polarization direction is adjusted by/2 wave plates. Finally, the polarization state of linearly polarized light is changed into arbitrary polarization state by/4 wave plates. The delay effect produced by the birefringence effect is mainly determined by the cladding radius of the fiber, the fiber ring radius and the wavelength of the light, the adjusted polarization state can cover the entire poincare sphere.   


Application area

 


  • Single mode to polarization-maitaining fiebr
  • Polarization-related loss measurement.
  • Polarization-sensitive device application
  • Fiber lasers
  • Fiber interferometers


 

Product structure diagram

 偏振控制器


Schematic diagram of polarization controller

 偏振控制器

 

Relationship between single-loop delay and wavelength , number of loops in polarization controller.(Test unit: fiber loop diameter 40mm, fiber cladding diameter 900µm)

For example: Polarization controller fiebr loop fixed diameter of 40 mm, the cladding diameter of 900µm of tight-sheathed fiber around in the ghost.

When λ=1550nm , and loop number =1 , the ring is equivalent toλ/2 wave plate.

When λ=1550nm , and loop number =3, the ring is equivalent to 3λ/2 wave plate


想知道这个产品吗?

发送 信息
留言

如果您对我们的产品感兴趣并想了解更多详细信息,请在此处留言,我们将尽快答复您。

相关产品
光话机 光话机/稳定光源一体机、光电话、光纤电话机
全双工数字语音通信功能 话音清晰,背景噪声小 提供在线显示及呼叫功能 大屏幕显示 电池电压提示
多通道高速光功率计模块 多通道高速光功率计模块
外形小巧、尤其适于系统集成及二次开发; 启动快速、测量精度高 大动态测试 可选光功率探测范围 可选1~4通道光功率计 丰富的通信指令集及demo软件支持
多通道高速光功率计模块 多通道高速光功率计模块
3.5英寸彩屏显示 90dB的动态范围 最大支持45个校准波长 阈值设置通过/未通过告警功能 波长自动识别功能 PMAX/PMin  实时测试 频率光的检测功能 提供实时数据读取功能,方便嵌入系统应用 可视故障定仪功能 存储数据1000条
800G QSFP-DD 800G QSFP-DD SR8 850nm 100m MPO-16 APC
Features QSFP-DD Serial Optical Interface 8x100G PAM4 retimed 800GAUI-8 electrical interface MPO-16 APC connector 8 channel VCSEL arrays and 8 channels PIN photo detector arrays Maximum link length of 60m on OM3 or 100m on OM4 QSFP-DD MSA Compliant Hot Pluggable QSFP-DD form factor Compliant to QSFP-DD-Hardware-Rev 6.3 MSA Compliant to CMIS 5.2 Support Protocol Compliant to IEEE 802.3db Compliant to IEEE 802.3ck Low Power Consumption Less than 14W in temperature range of 0 to 70℃
10G SFP+  Transceiver 10G BIDI SFP+ Optical Transceiver
10G SFP+ optical transceiver module, support 10Gb/s and up to 100 km transmission, including: SFP+ SR, SFP+ LR, SFP+ ER, SFP+ ZR, etc. It works in high-speed IDC connection solutions, 5G network front-haul solution, network switch, PTN, OTN and so on.
以太网单向网闸 以太网单向网闸 千兆以太网单向传输设备 FW801
产品特点 物理隔离保障:光纤单向传输设备通过单向光纤通道,确保信息在传输过程中只能单向流动。这种物理隔离机制有效地防止了任何可能的信息泄露和未授权访问。 高度可靠性:我们的产品采用高品质的光纤技术和可靠的传输协议,确保信息传输的完整性和稳定性。设备内部的纠错和校验机制进一步增强了传输的可靠性,有效地减少了数据丢失或损坏的风险。 安装简单:无需复杂的安装流程,即插即用,简易上手。
空闲光纤管理系统:智能优化,高效管理,释放光纤潜力 空闲光纤管理系统:智能优化,高效管理,释放光纤潜力
特点: 1U机箱可接入48芯,24路双芯业务, 业务和检测同时接入,互不影响 设备断电(或故障)也不影响业务正常通信 实时监控与状态分析 - 光纤状态监测:实时监测光纤链路线损状态。 - 故障预警:自动识别光纤链路中的潜在问题,并及时发出警报,帮助维护人员快速响应。
网络分光器 16口MPO 网络分光器
支持8条40G/100G/200G MPO流量分光复制 低插损,不影响数据流量包。 无需电源,无需IP址址,无需MAC地址,100%无源产品,性能安全可靠 安装和操作简单,非专业人士即可独立完成。 16个OTAP端口 ,支持8路主链路串接,数据流量复制;可替代8个交换机镜象端口。 成本低,集成度高
留言
留言
如果您对我们的产品感兴趣并想了解更多详细信息,请在此处留言,我们将尽快答复您。

首页

产品

关于

联系